Zu Produktinformationen springen
1 von 7

Rhombus Access Control System

IC + EM/ID dual frequency DC5V WG26/34 Serial Port UART RFID Reader Module

IC + EM/ID dual frequency DC5V WG26/34 Serial Port UART RFID Reader Module

Normaler Preis $4.95 USD
Normaler Preis Verkaufspreis $4.95 USD
Sale Ausverkauft

 

 

Descripition:

 

Voltage: DC 5V

Current: 40mA

Support: read EM / ID 125kHz and S50 / S70 IC 13.56MHz cards

Support: read EM / ID 125kHz and S50 / S70 IC 13.56MHz cards

Interface: Wiegand, UART

 

UART module with 3pin cable,

WG module with 5 pin cable.

UART board only. If WG format is required, Please weld the wire yourself.

 

Interface Description:

5v  D1  D0/TXD  GND  CST

Power supply: DC 5V power supply, choose linear power supply can get better card reading effect

D1: WG outputs data1, Data0

The pin of Data0 or UART module output by d0 / TXD WG is the serial port data output terminal

CST: W26 / 34 format selection (hanging means W26, grounding means W34) also has other functions


Introduction to Wiegand interface output: 

  1. When a card is sensed, the serial number of the card will be output through Data0 and data1.
  2. Data0 and data1 are both high level without data output.
  3. Data bit 0: a 400 US wide low level is generated on the Data0 line.
  4. Data bit 1: generate a 400us wide low level on data1 line.
  5. The length of each bit of data is 2400us
  6. Each Mifare card has a 4-byte serial number. We output the last three bytes.
  7. Add the first 12 bit even parity check bit in the front, and add the last 12 bit odd parity bit after it, with a total of 26 bits of data.
  8. Card number: 6B 3D 12 D6
  9. Output data: 3D 12 D6

 

Weigand 26   

0

00111101  

00010010

11010110  

1

even parity

3D 

12

D6

Odd parity

 

Weigand 34 :  

0

01101011

00111101  

00010010

11010110        

0

even parity

6B

3D    

12

D6

Odd parity

 

 Uart Interface output:

Baud rate:9600

Start data

length

Card type

Card data

BCC check

End of data

0x02

0x09

0x01

SN0~SN3

Exclusive or operations other than the beginning and end of data

0x03

 

Among them, the card types are:

0x02  EM4100

0x01  MIFARE 1K

 

For example, the data received by the serial port tool is 02 09 02 04 2E 53 82 F03

 

The first byte, 0x02, indicates the beginning of the data.

The second byte, 0x09, indicates that the whole data length is 9 bytes, including data start and data end.

The third byte, 0x02, indicates that the card type is em4100.

The fourth byte to the seventh byte (0x04 0x2e 0x53 0x82) indicates the card number read.

The 8th byte, 0xf0, represents the BCC check from the 2nd byte to the 8th byte.

The ninth byte, 0x03, indicates the end of the data.


Package:

1x  rfid reader module  with 5pin cable(WG26/34)

or

1x rfid reader module with 3pin cable(UART 

Vollständige Details anzeigen